TSC TTP-244ME Bar code printer installation description
2.1 Install TTP-244ME TSC barcode printer
(1) Place the barcode machine after unpacking on a clean and flat desktop. At this time, do not turn on the power supply.
② Connect the two ends of the RS-232 or parallel connector to the printer and computer respectively.
③ Connect the two ends of the power cable to the printer and the power socket respectively.
2.2 Installing Labels and Labels
Note: Before installing labels, push the paper guide to both sides. If the labels you want to install are sticky stickers, please
Be careful not to let the sticker warped, avoid sticker adhesion to the print head, affect the print quality of the print head.
(1) Open the cover of the printer, open the front panel;
(2) Pull the release lever of the printing head frame to open the printing head frame;
③ Pull down the fixed axis of the label roll, insert the label roll (printing letters outward) into the center hole of the label roll, and pull back the label
Roll fixed shaft;
(4) According to the direction indicated by the arrow on the base printed with LABEL, roll the LABEL from the front end of the printing head frame, through the top of the pressure bar,
Then forward through the label exit pull out;
⑤ Adjust the guide according to the width of the paper roll to make it consistent with the width of the label roll;
⑥ Press down the printing head frame;
The label roll to the opposite direction of the roll tight, so that the label paper to keep the state of tension;
⑧ close the paper outlet box door and printer cover;
⑨ Turn on the power of barcode printer, the printer will automatically detect whether the carbon belt is installed, so as to set it as thermal sensitive mode or thermal transfer mode
Type.
2.3 Install the automatic paper stripping function
The peel off function is designed to use self-adhesive label stickers to send one label after printing
After signing the sticker, make it and the back paper automatically peeled. Ttp-244me Plus has an automatic peel off sensor built in
Sensor), so that the printer does not move until you remove the label sticker each time, and then continue to print
Print and send out the next label sticker as follows:
(1) Open the upper cover and the paper outlet box door;
② Install the label paper roll according to the above steps;
③ Press the FEED button to make the label roll out about 3 inches of label paper;
(4) Tear off the label sticker sent out, leaving the back paper;
(5) Put the back paper between the pressure rod and the paper removing rod, and then pull the back paper out from the bottom of the paper removing rod, and keep it flat without twists and turns;
⑥ Roll the label scroll back in the opposite direction, so that the label paper roll remains flat and without twists and turns;
After inserting the back paper into the back paper outlet, close the door of the paper slot box and close the top cover.
2.4 Installing carbon Belts
(1) Please turn off the power first and open the cover;
(2) the carbon is brought back to the reel and inserted into the empty carbon tape paper shaft;
(3) Insert the carbon belt reel into the carbon belt shaft;
(4) pull the release lever of the printing head frame up to open the printing head frame;
(5) Pull the front end of the carbon belt backward, through the lower part of the printing head seat to the top of the carbon back reel, with tape to the front of the carbon belt
The transparent part of the end is smoothly attached to the paper axis of the carbon reel;
(6) roll the carbon back to the reel clockwise, so that the transparent part of the front end of the carbon belt is flat attached to the reel, until the black carbon belt is seen;
The carbon belt is tightened so that there is no fold in the carbon belt;
⑧ Close the printing head frame;
⑨ Close the upper cover, turn on the power, and press the FEED button until the online indicator lights up and green.
2.5 Self-test Mode
To start self-test mode, press the power FEED key not to put and then open the barcode printers, into self-test mode right now, first of all, began to detect the printer installed on the printer the label paper length and the position of the label paper Gap (Gap), if the printer failed to find a Gap after detecting 7 inches, it will label paper as a continuous FEED, Then print out a Check Pattern for you to Check the current print quality of the print head, and then start printing the internal set value of the printer. At this time, you can release the paper feed button, want to leave the self-test mode, turn off the power, and restart the printer. The following are the printer internal Settings printed in self-test mode and their meanings:
⑴ The current printing mode and Firmware version of the printer
⑵ How much print length has been taken by the printer
⑶ the number of files downloaded to Flash Memory
(4) the Check Sum
⑸ Setting of the serial port
⑹ Special character set Settings (Code Page)
⑺ Country code setting
⑻ Print speed setting
⑼ Printing concentration setting
We will also set the size of the label
(2) Set the width and offset of Gap or BLINE on label paper
(12) Sensitivity of label gap sensor
How to download the file list stored in the Flash Memory
(14) Memory size available
After the self-test, the printer will enter the debugging mode. Please turn off the barcode printer and then turn on the power to make the printer correct
Normal print mode.
2.6 Driver Installation Methods
① Place the product CD-ROM into the CD-ROM drive and open the Windows Driver folder. ② Click bar code machine driver installation;
(3) Follow the instructions of the installation window to install; ④ Select Install Printer Driver mode. ⑤ Select the barcode machine to be installed
Model; ⑥ Specify printer connection interface; ⑦ Specify the printer name and complete; ⑧ Confirm all on the printer Settings page
After the installation Settings are correct, press the “Finish” keyboard to start copying driver files; ⑨ When driver files are copied
After the completion of the driver installation will be completed, in the Windows control panel “printer and fax” options will be added
The bar code machine that has just been installed
3, TSC TTP-244ME bar code printer operation instructions
3.1 Button and indicator Description
● Power indicator
The green power indicator light will be on when the power is turned on.
● Online indicator light
When the printer is on standby, the green online indicator light will be on, and when the pause button is pressed, the online indicator light will blink.
● Error indicator
When printer errors occur, such as memory errors, syntax errors, etc., the red error indicator light will be on; Lack of paper, lack of carbon
With such errors the red light will flash.
When choose a single bond
Ttp-244me Plus provides options that allow users to check printer status or set print parameters directly on the LCD screen
And so on. To enter the radio mode, press the radio key and continue to press this key to select other radio options or return to the original standby mode
State. The menu consists of the following five main options: printer information, file list, memory information, date/time,
Printer Settings. Each major option consists of a number of minor options that can be selected by selection keys or Settings
Key to view or set.
● Pause/select key
This button combines two functions: (1) if the printer is in the standby state is the pause button; ② If the printer is in menu mode
Below is the select key.
Pause button can let the user temporarily stop the execution of the work, to cancel the suspension state, please press the pause button again. Press the pause
After the key, the printer will stop after printing the label being processed. ② Online indicator flashing; ③ All that have not yet been printed
Is kept in memory. In this way, the user can change the label or carbon tape in neutral and press the pause button again
The printer started up again.
Note: If you press the pause button for more than 3 seconds, the printer will reset and all printed work data will be lost.
Low key into paper
Like the Pause/select button, this button also has dual functions: feed and setting.
Press the feed button to move the label roll to the starting point of the next label (depending on the type of paper and label length set).
Press the set key to check the printer status or change the setting of print parameters on the LCD.